GT2538C Model - 454203-0001 |
||||||
---|---|---|---|---|---|---|
Figure | Part Number | Description | Quantity | |||
3 | 434546-0005 | Caracola admisión | 1 | |||
2 | 400589-0375 | Retaining ring ( compressor housing ) | 1 | |||
4 | 403069-0164 | O ring ( compressor housing ) | 1 | |||
- | 443854-0150 | C.H.R.A. | 1 | |||
8 | 435209-0010 | Bearing housing | 1 | |||
23 | 430093-0016 | Bearing | 2 | |||
24 | 444428-0001 | Retaining ring ( bearing ) | 3 | |||
12 | 435354-0010 | Turbine wheel | 1 | |||
13 | 443594-0001 | Heat shield | 1 | |||
11 | 400749-0006 | Piston ring ( turbine side ) | 1 | |||
19 | 443852-0002 | Thrust collar | 1 | |||
22 | 432254-0002 | Thrust bearing | 1 | |||
21 | 400810-0410 | Screw ( coj. empuje ) | 3 | |||
15 | 432280-0001 | Plate insercción | 1 | |||
20 | 403069-0163 | O ring ( plato insercción ) | 1 | |||
14 | 400589-0181 | Retaining ring ( plato insercción ) | 1 | |||
17 | 403818-0009 | Piston ring ( compressor side ) | 1 | |||
10 | 447449-0010 | Compressor wheel | 1 | |||
9 | 435255-0001 | Shaft nut | 1 | |||
7 | 433077-0004 | Turbine housing | 1 | |||
6 | 432726-0001 | Clamp ( turbine housing ) | 2 | |||
5 | 400677-0816 | Bolt ( turbine side ) | 4 | |||
31 | 432753-0008 | Actuator | 1 | |||
32 | 433075-0001 | Bracket ( actuator ) | 1 | |||
27 | 432333-0001 | Nut ( actuator ) | 2 | |||
43 | 413885-0001 | Rod end ( actuator ) | 1 | |||
42 | 430893-0006 | Nut ( rod end actuator ) | 1 | |||
1 | 400724-0610 | Bolt ( actuator bracket ) | 2 | |||
28 | 400702-0025 | Retaining ring ( actuator ) | 1 | |||
100 | 210305 | Gasket ( turbine inlet ) | 1 | |||
115 | 210306 | Gasket ( oil outlet ) | 1 | |||
150 | 431411-0840 | Stud ( turbine housing inlet ) | 3 | |||
155 | 210411 | Stud ( turbine housing outlet ) | 2 | |||
Pressure actuator Type = vacuum | Angles | |||||
1 - 0.000 bar = 0.0 mm | δ (delta) = 165º | |||||
2 - 0.120 bar = 1.0 - 4.0 mm | ε (epsilon) = 286º | |||||
3 - 0.400 bar = 14.0 - 16.0 mm | ||||||
4 - 0.500 bar = no movement | ||||||
Balance VSR | ||||||
1.5G between 0 - 75.000 rpm |
Updated on August 17, 2008