21:38:46 - Thu, Nov 21, 2024 -
10°C
10°C466491-0005 Parts List
TB2566 Model - 466491-0005 |
||||||
|---|---|---|---|---|---|---|
| Figure | Part Number | Description | Quantity | |||
| 3 | 409589-0035 | Caracola admisión m. | 1 | |||
| 3 | 409115-0095 | Caracola admisión | 1 | |||
| 35 | 400698-0001 | Fitting ( compressor housing ) | 1 | |||
| 2 | 400589-0375 | Retaining ring ( compressor housing ) | 1 | |||
| 4 | 403069-0164 | O ring ( compressor housing ) | 1 | |||
| - | 431876-0059 | C.H.R.A. | 1 | |||
| 8 | 446931-0009 | Bearing housing | 1 | |||
| 23 | 432236-0003 | Bearing | 2 | |||
| 24 | 430064-0001 | Retaining ring ( bearing ) | 2 | |||
| 26 | 444379-0003 | Deflector ( bearing ) | 1 | |||
| 25 | 430765-0001 | Retén ( deflector bearing ) | 1 | |||
| 12 | 435922-0003 | Turbine wheel | 1 | |||
| 13 | 430871-0002 | Heat shield | 1 | |||
| 11 | 400749-0006 | Piston ring ( turbine side ) | 1 | |||
| 19 | 443852-0002 | Thrust collar | 1 | |||
| 22 | 432254-0002 | Thrust bearing | 1 | |||
| 21 | 400810-0410 | Screw ( coj. empuje ) | 3 | |||
| 15 | 432280-0001 | Plate insercción | 1 | |||
| 20 | 403069-0163 | O ring ( plato insercción ) | 1 | |||
| 14 | 400589-0181 | Retaining ring ( plato insercción ) | 1 | |||
| 17 | 403818-0009 | Piston ring ( compressor side ) | 1 | |||
| 10 | 447449-0011 | Compressor wheel | 1 | |||
| 9 | 435255-0002 | Shaft nut | 1 | |||
| 7 | 448586-0007 | Turbine housing | 1 | |||
| 6 | 467345-0001 | Clamp ( turbine housing ) | 2 | |||
| 5 | 400788-0816 | Bolt ( turbine side ) | 4 | |||
| 31 | 430819-0283 | Actuator | 1 | |||
| 1 | 400724-0610 | Screw ( actuator ) | 2 | |||
| 28 | 400702-0018 | Retaining ring ( actuator ) | 1 | |||
| 100 | 210621 | Gasket ( turbine inlet ) | 1 | |||
| 105 | 210622 | Gasket ( turbine outlet ) | 1 | |||
| 115 | 413709-0001 | Gasket ( oil outlet ) | 1 | |||
| Pressure actuator Type = Pressure | Angles | |||||
| 0.890 - 0.930 bar = 1.00 mm | δ (delta) = N/D | |||||
| ε (epsilon) = N/D | ||||||
| Balance VSR | ||||||
| 1.5G between 0 - 85.000 rpm | ||||||
Updated on June 22, 2009